Workshop Pengenalan Cacat Las Standar Internasional di LPK Immanuel Provinsi Sumatera Utara

Alexander Sebayang, Efrata Tarigan, Liwat Tarigan, Piktor Tarigan, Positron Bangun

Abstract


The Department of Mechanical Engineering of the Medan State Polytechnic (POLMED) has international standard welding practice and laboratory equipment. In line with the progress of this equipment, quite a number of teaching staff in this study program already have teaching certificates in the field of welding. The socialization of welding in this study program has received recognition from the Professional Institute International Welding (IIW) and The Welding Institute (TWI), so that the Mechanical Engineering Department has become a Competency Test Site (TUK) for IIW and TWI international certification. The proponent of this international standard welding defect recognition training program already has a CSWIP (Certificate Scheme Welding Inspection Personnel) 3.0 certificate from The Welding Institute. LPK IMMANUEL MEDAN has a Welding course training field, this is related to making vehicle frames (chassis & body). Participants who take part in this program have good achievements and are prepared to enter the world of work after being declared graduated with proof of a certificate. It is very reasonable for LPK IMMANUEL MEDAN to accept the offer of an international standard welding defect identification training program held by a lecturer from the Department of Mechanical Engineering, Medan State Polytechnic (POLMED). especially to hold welding inspection socialization based on TWI standards. This knowledge will prepare prospective LPK Immanuel graduates to enter jobs in the welding field. This program is very relevant to the adult world of work. With this training, LPK participants will gain insight into how welding results meet the TWI standard, which is a standard that is widely used in the international world. This is supported by experienced and certified lecturers who carry out the service above in the CSWIP 3.0 (welding inspector) training in the use of the welding gauge which will be donated to the LPK Immanuel. Through this program, welding inspection modules and welding gauges have also been donated so that LPK participants can use them in the future

Keywords


welding, vocational, TWI standards

References


Wiryosumarto, H. dan Okumura, T. Teknologi Pengelasan Logam. 2000. Jakarta, PT. Pradya Paramita

Taufik Akbar, Budie Santosa,. (2012). Analisa Pengaruh dari Welding Sequence Terhadap Tegangan Sisa dan Deformasi Pada Circular Patch Weld Double Bevel Butt-Joint Plat ASTM A36 Menggunakan Metode Element Hingga. JURNAL TEKNIK ITS Vol. 1, No. 1(Sept. 2012) ISSN: 2301-9271: 352 – 357

Teguh wiyono. (2012), Penentuan Pengelasan Dissimiliar Allumunium Dan Pelat Baja Karbon Rendah Dengan Variasi Waktu Pengelasan Dan Arus Listrik. Jurnal Foundry Vol. 2 No. 1 April 2012 ISSN 2087-2259 :20 – 25

Joko santoso., (2006) Pengaruh Arus Pengelasan Terhadap Kekuatan Tarik Dan Ketangguhan Las Smaw Dengan Elektroda E7018, Jurnal teknik mesin UNES Vol, III, NO 11, 22 september 2006 ISSN 2102- 7491: 206 – 220

Adi Nugroho, Eko Setiawan. (2018). Pengaruh Variasi Kuat Arus Pengelasan Terhadap Kekuatan Tarik Dan Kekerasan Sambungan Las Plate Carbon Steel Astm 36. Jurnal Rekayasa Sistem Industri Volume 3. No.2 ISSN (print) 2477-2089 (online) 2621-1262, 134-142.

Anang Setiawan, Yusa Asra Yuli Wardana. (2006). Analisa Ketangguhan dan Struktur Mikro pada Daerah Las dan HAZ Hasil Pengelasan Sumerged Arc Welding pada Baja SM 490. JURNAL TEKNIK MESIN Vol. 8, No. 2,, 57-63.

Azwinur, Saifuddin A. Jalil, Asmaul Husna. (2017). Pengaruh Variasi Arus Pengelasan Terhadap Sifat Mekanik Pada Proses Pengelasan Smaw. Jurnal Polimesin (ISSN: 1693-5462), Volume 15, Nomor 2, 36-41.

Dody Prayitno, Harry Daniel Hutagalung, Daisman P.B. Aji. (2018). Pengaruh Kuat Arus Listrik Pengelasan Terhadap Kekerasan Lapisan Lasan Pada Baja Astm A316. Jurnal Dinamika Vokasional Teknik Mesin, Volume 3, Nomor 1, 1-6.

Hamid, A. (2016). Analisa Pengaruh Arus Pengelasan Smaw Pada Material Baja Karbon Rendah Terhadap Kekuatan Material Hasil Sambungan. Jurnal Teknologi Elektro, Universitas Mercu Buana (ISSN:2086-9479), 26-36.

Efrata Tarigan, Alexander Sebayang, Sihar Siahaan, Sosialisasi Pengujian Cacat Las Standar Internasional Di Smks Gbkp Simpang Vi, Kelurahan Gung Leto, Kecamatan Kabanjahe, Kabupaten Karo, Provinsi Sumatera Utara (http://jurnalpkmibbi.org/index.php/Pubarama/article/view/32)




DOI: https://doi.org/10.47165/intancendekia.v4i1%20JunI.641

Refbacks

  • There are currently no refbacks.


Copyright (c) 2023 Alexander Sebayang, Efrata Tarigan, Liwat Tarigan, Piktor Tarigan, Positron Bangun